The ML385 model is the longest armrest in the Matchline series and is recommended for light and heavy trucks and some passenger cars. The armrest has dimensions of 385 x 85 x 67 (LxHxD), and is manufactured in left and right hand versions. The maximum load capacity is 250 kg. The adjustability is 60º. The lower section in standard PA6 is combined with different materials and colours on the upper section.
We recommend the MLC 310 armrest for retrofitting to the following vehicles, among others:
Citroen Berlingo, C3 Aircross, C4 Picasso, Jumper, Dacia lodgy, Fiat Ducato, Talento, Ford Tourneo, Transit, Hyundai H1, H350,
Land Rover Defender, Mercedes Sprinter, Citan, Vito, Nissan NV200, NV300, Peugeot Boxer, Expert, Renault Master, Kangoo, Trafic, Smart ForTwo, Toyota ProAce, Volkswagen Transporter, LT and more....
Look in the article configurator if your vehicle is included. Excellent material and processing • made in europe
• turn-up and adjustably
• easy mounting with special adapter
• price incl. adapter and material for installation
Notes on use
(You will find information about your vehicle in the article configurator)
0. There are no notes to be observed
1. The MLC310 armrest is not recommended to this car model.
2. The ML285 armrest is not recommended to this car model.
3. The armrest might increase on the possibility to use the storage compartment between the seats or kollide with
the console when the seat is adjusted in its lowest position.
4. Does not fit seats with a lumbar support function (Note: some models can fit if the adjusting wheel is on the
opposite side where the armrest is to be mounted)
5. If the seat is equipped with a side airbag -the armrest can not be mounted towards the door-side.
6. Does not fit seats original equipped with armrests or cars that have a high positioned center console that can
collide with the armrest.
7. The lid to the storage compartment between the front seats might have to be
removed -can collide with the armrest.
8. Can contain difficult mounting elements that might require special tools -contact if necessary your dealer for
advise or help.
9. The armrest can be mounted inspite of existing armrest (has to be removed before mounting).
10. Only sold as a complete set with armrest and adapter for both sides of the seat(right + left side).
11. Special adaption on separate order -the bracket is only delivered together with the armrest.
12. Fastening points must be drilled in the seatframe.
13. Can only be mounted on the driver seat if the passenger
seat is of the type -completely foldable or a double sofa.
14. Only fit seats with a prepared fixing point for original armrests. (see mounting instruction).
15. To be able to mount armrest MLC310 -you need a minimum space of appr. 135 mm between the seats.
16. Seats equipped with the function ”a completely foldable seatback” -you will only be able to partially fold the
seat together (approx 75%) after the armrest is attached to the seat.
17. If the seat is equipped with an adjustable backrest support -you can only use the MLC310 armrest (other
armrest models will collide with the adj.wheel).
18. Only available at brand dealers or by special request.
19. Only for the passengerseats / backseats (not frontseats).
20. Note! older adaption.
21. If the car model has a double sofa, then only the armrest PUR355 can be mounted.
22. Use this adapter if the seat has a lumbar support funtion. Otherwise choose adapter F1030-35005R/L.
(is already defined in the configurator considered)
23. Use this adapter if the seat has height adjustment function (is already defined in the configurator considered)
24. By mounting armrests on the seat, the possibility of adjusting the seat down in its lowest position is limited by
about 20% due to the armrest then colliding with the car's center
Information from the manufacturer can be found here :